Healthy & Safety: Creating a Successful Hazard Communication Program

Health & Safety: Creating a Successful Hazard Communication Program

Has everyone in your shop been trained on the hazardous chemicals they’re exposed to on a daily basis?

When OSHA revised its Hazard Communication Standard in 2012 to align with the United Nations’ Globally Harmonized System of Classification and Labeling of Chemicals, the final transition deadline of June 2016 was years away. In that time period, employers covered under HazCom were expected to train employees on the revised standard by December 2013, and manufacturers were expected to update all labels and safety data sheets to comply with the requirements by December 2015. And now, all employers covered under HazCom are expected to be in full compliance.

Has everyone in your shop been trained on the hazardous chemicals they’re exposed to on a daily basis? In this column, we’re going to talk about how you can create a safer, more informed workplace, as well as stay compliant with OSHA regulations.

Six Steps to Success

According to OSHA, a successful and effective hazard communication program can be accomplished in six steps:

  1. Learn about the standard, including and especially how it applies to your workplace. The standard, as well as guidance, interpretations and other educational materials, can be found at If you haven’t already, identify staff members who will be responsible for ensuring your shop is in compliance with the standard and facilitating training for all employees. Remember, these are ongoing responsibilities, not one-time tasks. In some cases, assigning backup employees is a good idea in case of turnover or shifting of duties.
  2. Prepare a written plan for your shop to indicate how you will address hazard communication at your facility. This plan should include a list of all the hazardous chemicals in your shop. When you start using a new chemical, it should be added to that list. Your shop’s HazCom plan does not have to be extensive or complicated. Chemicals can be listed by any sort of product identifier, but the same identifier should be used both on the label and the safety data sheet (SDS). Remember, chemicals come in all forms: liquids, solids, gases, vapors, fumes and mists.
  3. Make sure your chemical container labels are up to date. Keep labels on containers that have been shipped. When you transfer chemicals from bulk containers to smaller containers, make sure those containers are also labeled appropriately. The addition of pictograms on labels was intended to draw attention to the hazards of a particular product, as well as let employees (no matter what language they speak) identify those hazards quickly.
  4. Maintain safety data sheets (SDS) for each chemical in the workplace. Safety data sheets give detailed information for workers and are a requirement for every hazardous chemical. If you have old MSDS materials, make sure they’re replaced with the new ones. Each new shipment of a chemical should have a current version of the sheet. Also, make sure that all employees know where the SDS are located. If you’re using an electronic SDS database, there should be a backup paper copy.
  5. Inform and train employees. New hires should be trained upon entering the workplace. All employees should be trained when a new chemical or other hazard is introduced. Employees should know the general requirements of the standard, the location of hazardous chemicals in work areas and what the workplace hazard communication program includes. Shops need to make sure they aren’t just passing out information, but rather creating an environment where employees understand the information and are comfortable asking questions. Training must address: 1. Methods and observations that may be used to detect the presence or release of a hazardous chemical in the work area (such as monitoring conducted by the employer, continuous monitoring devices, visual appearance or odor of hazardous chemicals when being released, etc.) 2. The physical, health, simple asphyxiation, combustible dust and pyrophoric gas hazards, as well as hazards not otherwise classified, of the chemicals in the work area. 3. The measures employees can take to protect themselves from these hazards, including specific procedures the employer has implemented to protect employees from exposure to hazardous chemicals, such as appropriate work practices, emergency procedures and personal protective equipment. 4. The details of the hazard communication program developed by the employer, including: an explanation of the labels received on shipped containers and the workplace labeling system used by their employer; the SDS, including the format of the SDS (where each type of information is located); and how employees can obtain and use the appropriate hazard information.
  6. Review and adjust your program accordingly. Periodically, you should review your hazard communication program and measure its successes or shortcomings. No two programs are alike, so be flexible and open to suggestions from employees. In addition, remember to revise your program as new chemicals enter the workplace. Most importantly, your plan should always be accurate. Proactive monitoring of the workplace and the hazards within is critical to having a successful and compliant hazard communication program.

You May Also Like

Sticker Shock at the SEMA Show

This year’s SEMA Show held a new surprise for me — a secret drop-off at our booth in the form of a mysterious sticker.

There are always surprises at the SEMA Show, which is one reason why it’s such a special event. New faces to meet, old faces that you haven’t seen in a long time with which to reunite, new technological wonders … the list goes on and on.

This year held a new surprise for me, however — a secret drop-off at our booth. Visiting the booth one day to make sure the magazines on display were still neat and tidy, I noticed a roll of stickers on the table. Upon closer inspection, I saw that the stickers read: “Collision Repair Equal To Mechanical Repair Rates: Why Not?” And there was also a mysterious symbol that my wild imagination took to be the logo of some secret society. But it wasn’t so mysterious after all; the letter “Y” and the drawing of a knot was a visual representation of: Why + Not. Haha, very clever!

Keys To Making 2023 A Huge Success For Your Auto Body Shop

Stopping daily work to work “on” your business instead of “in” your business is essential in order to deliver change in the new year. 

Auto Body Consolidation Update: What Will 2023 Bring?

The bull market of consolidation is expected to continue in 2023 even amidst high inflation, rising interest rates and other challenges.

The Great Awakening: Collision Repairers Taking a Stand

Many repairers are now taking a stand, realizing they cannot conduct business the way they used to.

CARSTAR Fort Collins: Process Produces Performance

The new facility that CARSTAR Fort Collins moved into was designed with organization and performance in mind.

Other Posts

Are Collision Repairers Their Own Worst Enemy?

It’s always been easy for repairers to see insurers as the bogeyman that causes all of their problems, but insurers are merely taking advantage of repairers’ lack of business knowledge and acumen.

Are You Ready to ROCK in 2023?

Do you know a “rockstar” in the automotive aftermarket? Then it’s time to nominate them as a Vehicle Care RockStar!

BodyShop Business 2022 Executives of the Year

This year’s Single-Shop award winner is Michael Bradshaw of K & M Collision in Hickory, N.C., and the Multi-Shop winner is Matt Ebert of Crash Champions.

Conducting Collision Business: It’s a New Day

The goal is not to declare war against insurers; it is to declare independence for your organization so that you’re able to provide the highest level of service to your true customers.