Scanning and Recalibration: Addressing the Myths - BodyShop Business

Scanning and Recalibration: Addressing the Myths

The phrase, “scan to cover all diagnostics,” is being heard a lot in our industry, which creates a problem as a recalibration or a reprogram is not a scan. So let’s address some of the myths floating around out there.

The new vehicle electronics are here to stay. It’s very important that we learn how they work and what they do. The repairs and required procedures for operation must also be learned and followed. Nobody wants to put a vehicle deemed not completed or unsafe back out on the road – that we all agree on.

We need to make sure we’re all talking the same language. The phrase, “scan to cover all diagnostics,” is being heard a lot in our industry. This creates a problem, as a recalibration or a reprogram is not a scan. There is a huge difference between them.

We also have so many myths floating around out there. The auto glass industry has been dealing with recalibrations for awhile as many newer vehicles require a recalibration after the windshield is replaced. The comments heard on this procedure are frightening. Now, the same comments are being heard from body shops. So let’s address some of the following myths:

  • A scan is the same as a recalibration
  • All dealerships know and have been trained on the new vehicle electronics and diagnostic procedures
  • If there is no light on the dash, everything is fine
  • If I do not disconnect it, I do not need to scan or recalibrate the system.

Myth No. 1: A Scan Is the Same as a Recalibration

There are levels of access that are available through the OBD port. It all depends on the tools being used. A scan is a low-level diagnostic designed to read codes that are set by the vehicle as to faults that have occurred. A little higher level is the clearing of codes. Recalibration is at the highest level of access to vehicle electronics. Here we have access to vehicle programming and can rewrite if access is there. A recalibration is a resetting of sensors to be sure they are not out of “focus.” You can have a functioning system and still not function correctly, as the sensors are not aimed or recalibrated to detect what they were designed for.

If you’re reading this, you’re not blind, obviously. If you go to the eye doctor and are tested and it’s found that you need glasses, when you put on the glasses, you now see clearly what you’ve been missing. Now you’re recalibrated. The recalibration would be the difference between a vehicle stopping in front of a child who suddenly crosses the street or not stopping. It’s the reaction time that’s critical. A scan cannot tell if the system is aimed correctly, but a recalibration does do a scan. Most scanning equipment available today can’t do recalibrations, as they provide a totally different level of functions. Most recalibration equipment requires a laptop with dedicated software and external sensors or a target board to do a static test. The dynamic test involves hitting the road for a period of time. There is no one tool currently available that can scan and/or recalibrate all vehicles.

One point needs to be clarified: If you call a dealership or sublet to an outside service and ask them how much it will cost to do a scan on a vehicle, you’ll get that cost of a scan. When you call and ask for the cost of a recalibration, you’ll get a totally different price in most cases. Be sure to ask for the right service. When doing repairs, reference ALLDATA or the new I-CAR RTS website if recalibrations are
required. Note that recalibrations are required if stated, not an option. Some vehicles can calibrate themselves, but most do not.

Myth No. 2: All Dealerships Know and Have Been Trained on These Features

It’s too bad this is not true. A technician may have been trained, but the equipment may not have been purchased yet or the service writer or manager may not have enough background to know what needs to be done. On many occasions, you literally have to go into dealerships, look up the procedures and teach them what’s required for recalibrations. Be sure to look up procedures and let them know you’re sending for a recalibration, not a scan – those are two different procedures. Driving a vehicle and determining that it seems fine is not a test for proper operation of electronic systems.

Myth No. 3: If There Is No Light on the Dash, Everything Is Fine

Mandatory recalibrations are performed to aim the components and be sure they detect what it’s their job to detect. You can have a totally functional system and still be blind. The light on the dash is for the owner to alert them that service is needed right away. DTCs do not always present a light; they’re just detecting abnormalities and recording them. If a serious abnormality arises, then the light will present itself to warn the driver.

Myth No. 4: If I Do Not Disconnect It, I Do Not Need to Scan or Recalibrate the System

Many sensors are designed to work a specific point of a vehicle. When the part is removed or misaligned due to collision and/or repairs, we must be certain that the sensor is realigned to the parameters required. Just because you did not disconnect the part does not mean it’s aimed correctly from the trauma of the crash or work performed. This also applies to the statement, “Well, I disconnected the battery first then put it back together and hooked the battery up.” You still have to be sure all is aimed and aligned properly. Glass techs tell shops, “Just let the camera on the glass hang by the wires. That way when it’s put back on the glass, it’s ready to go.” So the question is this: If the bracket is incorrectly mounted 1 mm in any direction or the new windshield is set 1mm too low, how will that affect a camera 100 feet down the road when it tries to see a stop sign or pedestrian? This also applies to the R&I of bumpers and other components. If improperly aligned, the sensors will be restricted or blind in function.

You May Also Like

New Welding Technology: Good or Bad?

Welding technology in the collision industry has advanced tremendously. But is the industry allowing techs to avoid the “why” in welding?

In the highly competitive automotive industry, change is inevitable. Manufacturers are challenged to meet new government standards in fuel economy as well as improve safety in their vehicle designs. Engineers consider many factors when developing materials to be used in the manufacture of their vehicles, including safety, fuel efficiency, manufacturability, durability, quality and environmental friendliness. 

Vehicle Scanning & Calibration Technology

Scan tools and calibration equipment have come a long way as far as ease of operation and ability to access the vehicle.

Welding on a Hybrid or Electric Vehicle

As more and more HEVs and EVs roll into your shop, there are considerations to take when welding.

Is Auto Glass Replacement Right For Your Auto Body Shop?

With ADAS features, required calibrations for auto glass and the variety of repairs currently being done in shops, glass seems an obvious fit to today’s business model.

Vehicle Calibrations and Mechanical Repairs

Whether you’re replacing a radiator or repairing collision damage, deviating from OEM requirements will make a shop a target for blame should something go wrong.

Other Posts

I-CAR Talks Scanning/Calibration Training

Jason Stahl talks to I-CAR’s Scott Kaboos and Jeff Poole about their scanning and calibration training courses.

Mazda Blind Spot Monitoring System Calibration

Joe Keene, automotive content video producer at Babcox Media, discusses how to calibrate the blind spot monitoring system on a 2020 Mazda 6 Grand Touring.

Lexus and Toyota Camera Calibration

Joe Keene, automotive content video producer at Babcox Media, discusses how to calibrate the camera on a 2021 Lexus UX where the camera was removed and reinstalled.

Car ADAS Aims for Precise Calibration

Jason Stahl talks to Car ADAS CEO Greg Peeters about his mission to bring a safer and more efficient calibration process to the collision repair industry.