The Database Enhancement Gateway has released an update
on its efforts to work with the information providers to automate "raw
plastic prep" in the estimating platforms.
The DEG’s stance is that if refinishing a raw plastic
part requires additional labor and materials, the repair estimate/invoice
should reflect this. However, the DEG states that getting this to happen was
difficult for two reasons:
Uncertainty as to which specific plastic parts are shipped raw and which are shipped primed
Until recently, the information providers didn’t provide
logic enabling the automated calculation of this additional refinish labor. The
result was that raw plastic preparation had to be determined on a case-by-case
basis and then manually calculated, often resulting in ongoing friction between
repairers and insurers.
In 2009, after much research, the DEG published a matrix
detailing the shipped condition of the majority of bumper covers which is
available on its website.
The following is a summary submitted by the DEG detailing
how each information provider has thus far responded to the raw plastic prep
issue:
CCC
According to the DEG, CCC provides the following language within its Motor
Guide to Estimating:
Unprimed Bumper Preparation
25% of the bumper’s base refinish time
Maximum time allocation: 1.0 hours
Does Not Include:
Removal of mold-release agents as outlined by
manufacturer
Masking (if required)
Application of adhesion promoter
Correction of pre-existent surface imperfections
Material Costs
The labor value generated by the above formula is
available as an automated calculation for the following makes by selecting
"ADDITIONAL OPERATIONS" within the bumper section:
Toyota
Lexus
Scion
Nissan
Infiniti
Subaru
Hyundai
Volvo
Mitsubishi
Saturn Astra and Aveo only
GM G8 and GTO only
Kia specific models only
When highlighting the part for bumpers that are known to
always arrive UNPRIMED, the following footnote appears:
PARTS: Component comes unprimed from OEM. Preparation is
required. See ADD IF REQUIRED operation.
When highlighting the part for bumpers that are known to
sometimes arrive UNPRIMED, the following footnote appears:
PARTS: Component may come unprimed from OEM. Preparation
may be required. See ADD IF REQUIRED operation.
Within "ADDITIONAL OPERATIONS", the available
operation reads as "Prep Unprimed Bumper." The DEG says that CCC/Motor indicates they’re considering the feasibility of
coverage for non-bumper parts in the future.
Audatex
The Audatex Database Reference Manual (DBRM) contains the
following language: Audatex refinish allowances start with priming a part. Due
to the differences in the paint manufacturers’ procedures, OEM recommendations
and the unpredictable nature of parts, any preparation required for raw,
unprimed bumper covers or other plastic parts is "Not Included" in
Audatex labor allowances. This operation may be added manually, if required.
The Audatex formula for preparation of a raw, unprimed bumper cover or plastic
part is 20 percent of the base refinish labor.
NOTE: Audatex will begin to add a "Prep Raw Bumper
Cover" operation to the Bumper Cover part choice box for new and updated
vehicles, beginning with Q1 2011. This will apply only to manufacturers known
to supply raw, unprimed bumper covers. The Audatex formula for Prep Raw, Unprimed
Bumper Cover is 20 percent of the base refinish allowance, with a .3 minimum time.
According to the DEG, at this time, the calculated result of the above formula
is available in the Audatex "Part Choices" box for the following
makes:
Toyota
Lexus
Scion
Mitsubishi
Subaru
Nissan
Infiniti
Hyundai
Kia
The prompt reads as "Prep Raw [Front/Rear] Bumper
Cover." According to the DEG, Audatex indicates that there is the possibility of coverage for
unprimed, non-bumper parts in the future.
Mitchell
According to the DEG, Mitchell presently provides no automated calculation of
raw plastic prep within their estimating platform. The Mitchell Collision
Estimating Guide (CEG) contains the following language:
Raw Substrate Prep Allow .2 per refinish hour (20 percent) for
plastic components that come from the manufacturer in raw/unprimed state.
According to the DEG, Mitchell estimating users seeking to capture Raw Plastic
Prep labor/materials must continue to do so via a manual line entry.
Education Needed
The DEG believes that estimators need to be educated as
to how these prompts are accessed within the estimating systems. The DEG
advises shops to review the underlying formulas to determine if they reasonably
match with shops’ specific processes and adjust if necessary.
The DEG says yet to be addressed by the information
providers are the many other plastic parts that may similarly ship in raw
condition, such as rocker moldings and side claddings.
"The information provider solutions that we outlined
above will be of even greater value if and when they include these non-bumper
plastic parts," says Arthur Harris, DEG administrator. "In the meanwhile, raw bumper
preparation for these non-bumper parts will have to be manually
generated."
More information: